How to Installation wall mounted pool light

HOW TO INSTALLATION: 1.Fix the bracket on the wall of the pool with screws. 2.Screw the lamp to the bracket, align the hole, and fix it with screws. 3.Connect the wires to a 12V-24V transformer(lamps cannot be directly connect to 110V or 220V power ). It is strongly recommended to use an underwater cable gland. Please install it underawter under the guidance of a professional electrician

NICHED VS. NICHELESS POOL LIGHTING OPTIONS

NICHED VS. NICHELESS POOL LIGHTING OPTIONS [Niche" refers to the pool light housing. Niched pool lights are generally larger in size and require advanced planning for placement during the rebar installation phase. "Nicheless" lights are smaller and don`t require a niche or special accommodation with the rebar. You can sufficiently light most swimming pool designs with either one or two niched pool lights. Alternately, you can use multiple nicheless lights with little to no difference in energy consumption. Plus, with more lights spread throughout the pool, more even light distribution will be attained - making it an aesthetic decision. View our Light Design Guide to see how nicheless lights can light different features of the pool. Your pool designer can help you determine the best pool lighting options for your pool design.

How To Change A Swimming Pool Light

How To Change A Swimming Pool Light If you are looking for information about how to change a swimming pool light then this article will help to explain the different kinds of pool lights that you can encounter and what you need to know about how to safely remove it from the light niche and install a new bulb. Before proceeding with a repair like this on your own you must be aware that water and electricity do not mix. Pool lights should not be dangerous and yet many of them are (or can be) due to improper installation or damage to the light. You should not, under any circumstances, attempt to work on, modify or change your pool lighting system in any way. Doing so could be dangerous or even deadly to yourself or any swimmers in your pool. I can not stress this enough - if you have any doubts about what you are doing then you should absolutely bring in a professional to assist you. All that being said there are many pool lighting systems which do not require that you do anything to the electrical system in order to change a burnt out bulb. In a properly installed pool light there is almost always a GFCI breaker that controls the lighting circuit. A GFCI, of GFI as it is often shortened to, protects against electrocution by detecting current escaping the intended system pathway. In the event of current leaking to ground, or a "ground fault" the GFI breaker will open the circuit. If you are working on your pool lights and want to change the bulb then the first step is that you must verify that this pool light is installed safely. Deficiencies and dangerous code violations like not having a ground fault protected circuit for your pool light would typically be found by an industry professional when doing routine maintenance such as changing the bulb in the pool light. If you are changing your own pool light then

How to low pH level

Before doing anything, always test your water first. Use a pool test kit to check the pH, acid demand, and total alkalinity. Once you`ve determined that the pH level is too high, you should now work to restore the balance. There are two main products for lowering the pH. These are sodium bisulfate (also known as dry acid) and muriatic acid. Here are the steps for each product: Sodium Bisulfate 1. Read the manufacturer`s instructions and measure the correct amount based on your initial testing. Some suggest adding ¾ of what`s recommended to allow for easier correction. 2. Sodium bisulfate usually comes in powder form. Avoid using it on a windy day to avoid blowback to your skin and clothes. 3. Add the chemical by getting down to the water as close as you can and downwind from you if it`s windy. Apply it over the water return jet site to facilitate spreading the powder throughout the pool. 4. The powder should dissolve on its own after ten to fifteen minutes

New design patant private moudle products

Mini Ultra thinnest new design underground pool led lights porduct are planning online for selling on about 10th.April,Let us look forward together.

Thank you Qshine Team

Although this year has been met with some challenges for our associates, our Facilities team has never stopped working hard to keep things running smoothly across the company! Thank you, team! Your efforts are greatly appreciated during these uncertain times.